Accessories  
 
Propeller Kits & Rubber Hub
Rubber Hub
Propeller Accessories
Besides propellers for many popular makes of outboard motors, SOLAS also provides a large section of propeller hardware for proper installation.
Understanding Boat Propeller Assemblies
On the Propshaft
A typical recreational boating propeller is mounted on a splined propshaft with a thrust washer, spacer, washer and nut, with some provision to keep the nut from turning loose, such as tabs on the washer or an additional cotter pin. There are exceptions, like the shear pin systems that were once widespread, but now most are as we describe here.

Thrust Washer
The thrust washer is mounted on the propshaft, between the lower unit and the propeller, and it may or may not have splines. It's an important component of a boat propeller's installation, because it fits the shaft in such a way that will not allow either itself or the propeller to move forward under thrust, thereby transferring thrust to the shaft and protecting the gear housing and its seal from contacting the rotating propeller.
A matching taper on the propshaft and the washer is one effective design that stops a thrust washer from moving too far forward.
The thrust washer also helps to keep the propeller centered on the shaft when the soft inner prop hub fails to do so under adverse high-torque conditions.

Hub
Inserted in the prop is a splined inner hub, which serves as a shock absorber between the prop blades and the shaft. A good prop hub should keep the propeller precision-centered on the propshaft, dampen vibrations and help protect the shaft from the severe shock of striking a submerged object with the propeller.
There are two basic types of hub (in addition to some rare specialty hubs): a pressed rubber hub or an interchangeable hub. The pressed hub is semi-permanently forced into position by a high pressure press in a prop shop. By contrast, the interchangeable hub is easily inserted by the prop installer. Each propeller is designed to use one type or the other. While pressed hubs are made of rubber, interchangeable hubs are sometimes made of a more rigid material, but we find that rubber interchangeable hubs offer better vibration dampening.
What's the difference between Rubex and Solas? Most Solas propellers are of the pressed rubber hub type and a few have specialty pin drive hubs. All Rubex props use interchangeable rubber hubs. There you have it!

Spacer
Like the thrust washer, the spacer assists alignment of the prop to the shaft when the inner hub is unable to hold its shape, only this time at the aft end of the prop.
The spacer bears reverse thrust loads and prevents the inner hub from moving aft, with its large surface area. The final washer and nut prevent the spacer from moving aft.
Many spacers are splined and some, for numerous Mercury, Mariner and Mercruiser applications, are also cogged or pinned to work in conjunction with an outer tab washer to prevent the nut from turning loose.

Washer
The washer helps fill space between the spacer and the nut, where the splines on the propshaft end and the threads begin. This helps prevent fore and aft play on the shaft by the prop.
A tab washer can be used if the spacer is designed for one. Otherwise, a large traditional washer would be expected on an assembly that uses a cotter pin to retain the nut.
When used, a tab washer's primary function is to prevent the nut from rotating in relation to the spacer.

Prop Nut
The prop nut secures the prop to the shaft and helps transfer reverse thrust to the shaft.
Normally made of brass, a nylon locknut is used in conjunction with a tab washer or else a castellated (castle) nut is used with a cotter pin.

Cotter Pin
Where used, the cotter pin passes through a hole in the propshaft after the castle nut has been tightened with its slots aligned on both sides of the hole.

Conclusion
With so few pieces, a prop assembly is not complicated. Because each of the parts in the prop assembly performs an important function, it is important to use the correct parts and to install them all as intended. To maintain the correct positioning, spacing and integrity, each part must be made to match both the propeller and the drive unit that it's going on.
Whenever doing a propeller installation, use your knowledge and pay particular attention to any instructions that may be provided with your prop or hub kit, especially concerning which parts to use.

Note:All the Original kits(O.E.M) are still usable.

Rubber Hub
After many years of research and development, SOLAS has developed an advanced series of rubber bushings with a strong and durable rubber compound. With the required equipment the rubber hubs are designed to install simply by pressing them into the hub with minimal of effort. However, they still offer excellent gripping force to keep the propeller from slipping.
Group
Engine Brand
Part Number
Parts
Fit O/E Propeller
2.5HP
Suzuki
1704003
S5-RB
NO
5~9.8HP
Yamaha
Tohatsu
Honda
Suzuki
1703001
1705001
170600
1704001
Y5-RB
T5-RB
H5-RB
S6-RB
NO
YES
NO
NO
Yamaha
Tohatsu
170300
170500
Y8-RB
T8-RB
NO
YES
A
Mercury/Mariner(~95)25mm
Yamaha/Honda
BRP/OMC/Evinrude/Johnson
Suzuki
Tohatsu/Nissan
170110
170310
170210
1704101
170510
MA-RB
YA-RB
OA-RB
SA-RB
TA-RB
YES
YES
YES
YES
YES
B
Mercury/Mariner
Yamaha
BRP/OMC/Evinrude/Johnson
Suzuki
Tohatsu/Nissan/Honda(S/S Prop)
Tohatsu/Nissan/Honda(Amita)
170120
170320
170220
170420
1705201
1705202
MB-RB
YB-RB
OB-RB
SB-RB
TB-RB-1
TB-RB-2
YES
YES
YES
YES
YES
NO
C
Mercury/Mariner
Yamaha/Honda
BRP/OMC/Evinrude/Johnson
Suzuki
Yamaha/Honda/Tohatsu/Nissan
170130
1703301
170230
1703301
1703301
MC-RB
YC-RB
OC-RB
YC-RB
YC-RB
YES
YES
YES
YES
YES
D
Mercury/Mariner/Honda
Yamaha
BRP/OMC/Evinrude/Johnson
Suzuki
Tohatsu/Nissan
Force(~94)
170140
170340
170240
170440
170340
170340
MD-RB
YD-RB
OD-RB
SD-RB
YD-RB
YD-RB
YES
YES
YES
YES
YES
YES
E
Mercury/Mariner/Honda(Amita)
Mercury/Mariner/Honda(S/S)
Yamaha(Amita)
Yamaha(S/S)
BRP/OMC/Evinrude/Johnson(Amita)
BRP/OMC/Evinrude/Johnson(S/S)
Suzuki(Amita)
Suzuki(S/S)
170150
170150
170350
170350
1702502
1702501
1704502
1704502
ME-RB-2
ME-RB-2
YE-RB-2
YE-RB-2
OE-RB-2
OE-RB-1
SE-RB-2
SE-RB-2
YES
YES
YES
YES
NO
YES
YES
YES
F
Mercury Bravo Two
170160
MF-RB
YES
Volvo Penta
Aquamatic SP(Long Hub)
SX Drive(Amita)
SX Drive(S/S)
Front Dual PROPS(S/S)
Rear Dual PROPS(S/S)
Front Dual PROPS(Aluminum)
Rear Dual PROPS(Aluminum)
170710
1707502
1707501
1707401
1707402
1707404
1707402
VA-RB
VE-RB-2
VE-RB-1
VD-RB-1
VD-RB-2
VD-RB-4
VD-RB-2
NO
NO
YES
NO
NO
NO
NO

 

   

News l About Solas l Products l Prop Finder l Where to Buy
Online Retailers l Tech Support l Contact us

©2011 Solas Science & Engineering Co., Ltd. All Rights Reserved
E-mail: market@solas.com.tw